Karcher Pressure Washers 15209900 2018 Opening Procedure

Written By: Arthur Shi
  • Comments: 0
Karcher Pressure Washers 15209900 2018 Opening Procedure

Difficulty

Moderate

Steps

13

Time Required

No estimate

Introduction

Prerequisite guide only! Shows how to open the Karcher 15209900 electric pressure washer for servicing.

All body screws are 25mm T15.

  1. sTyv3aNB2dm4MfO2
    sTyv3aNB2dm4MfO2
    D5ZbsGfh5ZyvgrQ5
    cgc3nZYGHJLUxwK4

    • Before you begin, make sure to power off and unplug the device from the outlet.

    • Unscrew the output hose from the pressure washer.

  2. EBWTJQJvxAIWl2RR
    EBWTJQJvxAIWl2RR
    MHUOdQnUBNgZby1Y
    JJQHjA11NFPhgEhS

    • Unlatch and remove the yellow rubber strap.

  3. WZIEbM5oYdcE2Nr4

    • Use a T20 driver to remove the two 55mm-long screws securing the hand grip.

  4. KieVyE5DudJoAPJB
    KieVyE5DudJoAPJB
    epyU11vLeXSbBtaX

    • Remove the hand grip from the extension bars.

  5. GejtniRRWSLli5wc
    GejtniRRWSLli5wc
    Rgavs3HXQyLABqEX

    • Use a T15 driver to remove the six screws securing the top black plastic panels on either side of the device.

  6. Z21nN4HX5GBuiWlc
    Z21nN4HX5GBuiWlc
    CnQr3PdIFhcvZPQc
    YL4amS16wgUWGNVj

    • Remove the two plastic panels.

  7. 4XhUxZhSrZW4HDY4
    4XhUxZhSrZW4HDY4
    uRIaK6tDrcQHtfJb

    • Remove the two T15 screws securing the plastic feet—one screw on either side.

  8. 1OMyUwN3wEnJ3qft
    1OMyUwN3wEnJ3qft
    VJA2KqOF1vRnenSZ
    o66w1MC2IXZO5qoX

    • Unclip and remove the plastic feet.

  9. fkyCtREJdmWQW4gT
    fkyCtREJdmWQW4gT
    bnjfYkiAyFPbUefQ

    • Use a T15 driver to remove the ten screws securing the housing halves together.

    • Remove the T15 screw underneath the wheel axle.

  10. LGcMqoMCNRqw6Oex
    LGcMqoMCNRqw6Oex
    GRfIFvXqEympLqSO

    • Set the device on its side.

    • Lift the housing half away from the body.

    • If the housing half does not separate, check to make sure you removed all the body screws.

    • Remove the housing.

    • Screws may get stuck inside the plastic housing. Be careful not to lose any screws.

  11. ZwTrKUJiLJvBQjVi
    ZwTrKUJiLJvBQjVi
    kRVq2dtRgsuncNGm

    • Slide the power cord strain relief out its notch on the plastic housing.

  12. XEUfShGY45o5ephH
    XEUfShGY45o5ephH
    5RsBLcA2PuuPlLhm

    • Lift the motor assembly out of the plastic housing and set it aside.

  13. 4KrlWNS4rVPZvNNl
    4KrlWNS4rVPZvNNl
    gPTwA5x1aENRxsPp
    Ab2xCsdeEBTakaAP

    • Reassembly tip: Use these images to help reassemble the housing back around the motor.

    • Make sure that all five bushings are in place.

    • In order for the housing to fit properly, the bushings must fit in their respective mounts.

    • Make sure that the yellow tube is properly notched onto the housing.

    • Make sure that the power cord strain relief sits correctly in the housing notch.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Arthur Shi

Member since: 03/01/18

272267 Reputation

0 comments