Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement

Written By: Carsten Frauenheim
  • Comments: 0
Mk Diamond Wet Saws MK660 2010 Bottom Cover Replacement

Difficulty

Moderate

Steps

11

Time Required

No estimate

Introduction

How to remove the cutting head's bottom cover for device service or part replacement in a Mk Diamond Wet Saw MK660 2010.

  1. 1PxeDQYqBQ233hrw
    1PxeDQYqBQ233hrw
    IRyQRqTroDdkvOdI
    MdZQD1eHaLdr53Fb

    • Before you begin, make sure to power off and unplug the device from the outlet.

    • If the clear water pump hose is connected, remove it now.

    • Loosen the plastic knob holding the saw's cutting head in place.

    • Lower the cutting head while keeping it steady.

  2. tGXO5ZwpfDMQqleL
    tGXO5ZwpfDMQqleL
    nJuiajrrOlNUASWL

    • Unscrew the knob.

    • Remove it from the cutting head.

  3. qqmPylZjmBpUSer1
    qqmPylZjmBpUSer1
    D2vbW4t5NvitZ1r2

    • Loosen the plastic knob holding the blade cover in place.

  4. GeVKq3xu1LCI4Du2
    GeVKq3xu1LCI4Du2
    DbWeQbHwT1KeG1Ie
    2PiWwbLoYillPmVG

    • Loosen the wing nut on the blade cover pivot shaft.

    • Remove the wing nut and accompanying washer.

  5. fPx4CnQEso32iGJU
    fPx4CnQEso32iGJU
    IZZQ5RAsvjexgUmO

    • Pivot the blade cover up and pull it off the shaft.

  6. w41FMjgfuCUIBRpP
    w41FMjgfuCUIBRpP
    Dh4MCJUQIXSRK3RT
    NOvXH6sJbmxgWexv

    • Insert the provided spanner wrench into one of the four tightening holes on the inner flange behind the blade.

    • Use the the provided nut wrench to loosen the hex nut while providing counterforce with the spanner wrench.

  7. 1QIYZfoE4BmFgILE
    1QIYZfoE4BmFgILE
    Q1HRZtiQlkNXhHFs

    • Remove the hex nut.

    • Remove the outer flange.

  8. PSceQ2bcDGNsB2c2
    PSceQ2bcDGNsB2c2
    BdaSZvt3XVxDU1o2

    • Remove the cutting blade.

    • The blade can be sharp, so handle with care.

  9. cZmwpLxSYu1nrDEX
    cZmwpLxSYu1nrDEX
    1KVmSJCbG5yKvg3x
    G6JsIicNOl1dckgX

    • Pull the entire cutting head straight off the shaft holding it in place.

  10. xReqlPglgF5aDrRa

    • Remove the eight Phillips #2 screws on the underside of the cutting head.

  11. QitO1sed2Re1RGOy
    QitO1sed2Re1RGOy
    kIQHLVNWTyKKwWdo

    • Remove the bottom cover.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

Carsten Frauenheim

Member since: 10/03/20

130778 Reputation

0 comments