Zune Flash 2nd Generation LCD Display Replacement

Written By: ybahman
  • Comments: 2
Zune Flash 2nd Generation LCD Display Replacement

Difficulty

Moderate

Steps

14

Time Required

15 - 20 minutes

Introduction

How to remove and replace the Zune Flash 2nd Generation LCD Display.

  1. cZNVSDKxLANam1Lf
    cZNVSDKxLANam1Lf
    GhqZThoP1NZMjoOp

    • Prior to disassembly, verify the hold switch is engaged to ensure the device will not turn on during the procedure.

    • If the device turns on while it is being disassembled it could cause irreversible damage to the device.

    • PICS MAKE NO SENSE.

    Tbh I came to see what the battery looked like so I can order the right one. I learned 2 really good things from this post actually. I learned these used clips and not glue as well S the proper battery. Thanks ifixit peeps. Also, sickcodes is the man and you guys should totally work with him more often. You guys are great as well. -- sanad

    sanadnesheiwat0301 -

  2. AKcHedyLTnHPynaI
    AKcHedyLTnHPynaI
    eTLJHFfpnM5r3uJv

    • Remove the top metal clip by inserting a Zune opening tool in between the faceplate and back cover and pulling gently back as shown in the images.

    • You should hear a 'click' as the clip detaches from the device.

  3. UwdBafxnhEtBTKcO

    • Remove the two screws shown using a Y00 Tri-Wing screwdriver.

  4. IQbQgPhFdoL1BkVu
    IQbQgPhFdoL1BkVu
    L2IW64EJBkJbBrsL
    VHjWIbBMOA14ii2X

    • Insert the Zune opening tool between the faceplate and the back cover, starting from the top and slowly work your way around the device.

  5. feG6OM1wmGP1FQry
    feG6OM1wmGP1FQry
    FrMDPG1ZBegVmpWk
    epBSXVwFT4kDMcjF

    • Work your way around the Zune until the back cover comes free. Remove the back plate and set it aside.

  6. 5WiFpCFCqDTUBLDg
    5WiFpCFCqDTUBLDg
    HqqkmwI2pT4HFQEf

    • Remove the three screws (5.5mm by 3mm) from the backside of the Zune using a Y00 Tri-Wing screwdriver.

    • Be sure to put this set of screws aside since they are a different size than any other screws in the device.

  7. XrditUaZgJXGy4FL
    XrditUaZgJXGy4FL
    Hh42TeBfxtYxGcHM

    • Use your finger or a Zune opening tool to pry back the two clear flaps.

    • Next lift the communications board that was being held down by the clear flaps.

    • Be careful not to accidentally detach the slim ribbon that connects between the communications board and the device.

  8. XnrGdutZddlXQxhE
    XnrGdutZddlXQxhE
    CrZFtwvDYqPerboP
    aVBSnmLntwVNSaiE

    • Disconnect the ribbon with the plastic opening tool by flipping up the black plastic flap where the ribbon connects to the memory board.

    • Carefully pull the ribbon out of the memory board, ensuring that the black plastic flap is up before removal to avoid the ripping the ribbon.

  9. Pg6DB2kdd4u45u42
    Pg6DB2kdd4u45u42
    WKmvIMrna1Yw6amR
    LEAHrdR2hCPRaJlI

    • Remove the battery by prying the battery off from the bottom with a Zune opening tool.

    • There is an adhesive between the battery and the device, therefore use a metal spudger to finish detaching the battery.

    • Be sure not to puncture the battery in any way when using the metal spudger.

  10. QQs6ZHOEAVTYJA45
    QQs6ZHOEAVTYJA45
    fO3TtRNgOBSHQVtK

    • Remove the single screw under the battery using a small Tri-Wing screwdriver.

  11. oyyP4CBx3kAmq6pM

    • Disconnect the faceplate from the device by depressing the two tabs located near the middle of each of the sides using a metal spudger.

    • This will disconnect the last circuit board in the device from the center frame.

  12. 1DLaMuHNA1koQ6Xd
    1DLaMuHNA1koQ6Xd
    uF6AC5EW1go6TCpA
    smLQxBkmIF2PAMiP

    • Remove the faceplate by using a metal spudger to separate it from the remaining components.

  13. WOwIGHMYLfVQGXoK

    • Release the LCD connector ribbon by flipping up the black switch. This will disconnect the LCD from the device.

    • At this point the LCD screen should be easily separable from the device.

  14. JbCUKnSadPuUH4Tn
    JbCUKnSadPuUH4Tn
    2bK6nKGDRlIapC1Q
    Q5WgEAwkJmpxEUgs

    • The LCD ribbon is adhered to the memory board with a strip of glue.

    • It's safest to flip the display over before removing the ribbon, as shown in the first image.

    • To avoid damage, remove the LCD by pulling slowly and carefully on the ribbon, directly away from the memory board.

    Be very careful here. The LCD ribbon is adhered to the memory board. I think the best way to remove it would be to pull it straight out, as in the image, although this can be difficult due to the ribbon being routed between the black frame and the rest of the device.

    Hayden -

Conclusion

To reassemble your device, follow these instructions in reverse order.

Author

ybahman

Member since: 02/11/09

139 Reputation

0 comments